Steps involved in the creative process!

I read something today that I would like to share with all of you.  When we look at items for sale that have been hand-made or hand-crafted, we often wonder, Why so expensive???  Well here are some reasons why this is.  In fact, we can ask the question “Why is the price so LOW?”

 

Courtesy of Adornyourself ( www.adornyourself.etsy.com ) , one of the fabulous artists on Etsy, I have quoted her post as of today, August 26, 2008 as follows:

“Adornyourself says:
I think we as craftspeople don’t always do as good a job as we can at letting buyers know what actually does go into producing a handcrafted item.

A pottery friend of mine has done and hands this to customer’s who ask why a handmade mug costs to much!

I challenge all of you to do this for the items you create and post it here.

Here’s Sams’..

so glad you asked!!)

1. Drive to Oakville and pick up the clay – 2 1/2 hour trip
EACH WAY.
2. Unload load clay into basement studio.
3. Weigh out amount needed.
4. Wedge (knead) clay.
5. Centre clay on wheel and throw the mug shape.
6. Remove from wheel and let dry 24 – 48 hours; depending on humidity.
7. Put mug back on wheel and trim.
8. Hand create handle.
9. Let handle dry 1 to 5 hours; depending on humidity.
10. Attach handle to trimmed mug
11. Cover handle in hot wax to slow drying on very dry days.
12. Let mug dry 1 week minimum. If mug cracks at this point,
re-cycle clay and start over at step 3.
13. Take mug upstairs to kiln in the garage and fire to 1850 F –
about 15 hours.
14. Take mug back downstairs to studio for glazing. If mug has
cracked during first firing, discard and write-off.
15. Mix glaze(s). Each glaze require approximately 3 hours to
mix and sieve.
16. Put hot wax on the bottom of mug so it does not stick to
kiln shelf.
17. Choose design and glaze mug.
18. Let mug dry thoroughly.
19. Bring mug back upstairs to kiln in the garage and load. If
glaze scratches or gets bumped on journey, wash with hot water and
start back at step 13.
20. Fire glazed mug to 2400 F. This takes 24 – 28 hours
depending on electricity demands.
21. Hold at 2400 F for approximately 25 minutes. Make sure all
shelves reach the exact same temperature.
22. Wait approximately 14 hours for kiln to cool to under 400 F
before opening.
23. Remove and check mug. If cracked, start over at step 1.
24. If mug has miraculously survived to this point, clean sharp
bits off bottom with grinding stone by hand, and put out for sale.
25. Last, but certainly not least instruction; try not to attack
the foolish person who innocently asks “Why does this mug cost
so much?”

AND, let us not forget all the hidden steps NOT numbered in here.

– Answer phone
– Sell pots
– Pay Ontario Hydro
– Develop new glazes and slips
– Come up with new pots and ideas
– Pay Ontario Hydro
– Put out signs on road
– Have MTO take signs off road
– Pay Ontario Hydro
– Re-cycle clay
– Pay Ontario Hydro
– Attend conferences and workshops

Thank you for your time and attention.

Sam

Feel free to modify to your routine, and hang where everyone
can see it!!  ”

 

So, in the spirit of things, I thought I would put in my 2 cents worth, and post some of what is involved in my sculpting with Fimo Polymer Clay.  Whether it be a Gift Tag Topper Ornament or a full sculpt.

 

“The steps to making a mug seem to be similar to sculpting for me, only I can bake it in my oven 🙂

Think of what I want to make
Draw it
Choose the colours
Knead the clay
Mix the clay (for colours) and hope to get it right the first time
Start the sculpt
Scrap the sculpt
Start the sculpt
Try to get rid of all finger / crease marks
Heat the oven (only 230 though)
Bake the sculpt
Let it cool completely in the oven
Fix any rough marks
Paint the sculpt (if applicable)
Glaze the sculpt (usually 5 – 10 steps)
Make the base (if applicable)
Glue on any embellisments to base and sculpt
Take pictures
Edit pictures
Decide you do not like the pictures and take more
Edit new pictures
Measure sculpt, and base in inches and centimeters
Write up the description
Figure out the tags
Guess the approximate price I HOPE to get
Make the box for the item
(which involves, measuring, cutting, glueing, embellishing etc)
Weigh and measure the boxed and packaged item
Get the shipping quote for Canada, USA and International
List the item
Market the item
Put it into my inventory books

Finally sell the item 🙂 ”

 

So, I for one will no longer be thinking in terms of “Oh, this is too much money” it will be more like, “I do hope they are making Some Money off of my purchase!!!”

 

Have a great day all!  And, please do not forget to stop by my shop to see all the new sculpts and other great gift ideas for your loved ones!  I also have a limited supply of commercial made supplies left, so come get them now while supplies last!  http://jewelzodonnell.etsy.com

Advertisements

2 responses to “Steps involved in the creative process!

  1. Hi Jewelz,
    Loved your directions in your post. Wish I had the time to create creations like you! You do nice work. Thanks for the informative post. 🙂

  2. Thank you for the compliment, Grouchow! You are very kind 🙂 I do love to sculpt, and find it is a very rewarding hobby.

    When I saw the post at Etsy explaining the process of creating a mug, I realized that there are so many steps to creating anything, and that I also wanted to be able to acknowledge the hard work that all artists put into their work.

    There have been quite a few responses to this post in the forum, and I have learned a lot!

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s